Global R&D Trends in 3D Printing

What?
Precise Planning of Orthognathic Surgery - Alveolar arches of the maxilla and mandibula of the models were replaced with orthodontic dental cast models. Temporomandibular joints of the models were fixed with Kirschner wire.

Why?
To increase accuracy in orthodontic surgery and prevention of condylar malpositioning and condylar sag by using life-sized, 3D models of our patients preoperatively.

What?
Surgical planning, three-dimensional model surgery and preshaped implants in treatment of bilateral craniomaxillofacial post-traumatic deformities.

Why?
Accuracy and efficiency and good therapeutic outcomes in the treatment of bilateral craniomaxillofacial post-traumatic deformities.

What?
Models can be used as templates to form titanium mesh implants, which are then used in the reconstruction of orbital floor defects.

Why?
Make it easier the process of fitting and aligning difficult implants, time consuming and operator dependent.

What?
Biomodeling in complex surgery in patients with craniofacial, maxillofacial, skull base cervical spinal pathology.

Why?
Better communication with patients and other surgeons, help diagnosis and operative planning, and surgeons to rehearse procedures readily.

What?
Diagnosis and treatment planning of maxillary canine impaction by using computed tomography combined with rapid prototyping.

Why?
Treating an impacted maxillary canine requires identifying its exact position; this can pose a challenge to both orthodontists and oral surgeons.

What?
A high-fidelity, inexpensive middle ear simulator could be created. Expert otologists will rate the SMS as having a high degree of realism in terms of shape and mechanical properties of the human middle ear affected by otosclerosis.

Why?
Inexpensive surgical middle ear simulator enhances surgical training for novice surgeons.

What?
Prototyping of temporary bone for surgical training and medical education.

Why?
Scarce availability of temporary bones for trainee.

What?
Mirror technique and rapid prototyping techniques were applied to design and prefabricate the individualized template for the preoperative repair of orbital inferior wall and maxillary anterior wall defects.

Why?
Improve surgical accuracy.

What?
Significant reduction in operative time with prototyping in craniofacial surgery: using a positioning guide after zygomatic osteotomy.

Why?
The management of post-traumatic deformity in the midface region poses challenges for the maxillofacial surgeon.

What?
Operative Dentistry Education - dentistry, where 40 students used 3Dprinted models versus standard schematics and photographs for cavity preparation.

Why?
Many students struggle for visual recognition. This is because 2D images and illustrations make it more difficult to identify and view the angles and walls of cavity preparations; also, when the prepare technique is demonstrated by a teacher in real teeth, the students' field of vision is limited, making it difficult for them to learn.

What?
Designing and manufacturing an prosthesis headset.

Why?
It reduces many of the preliminary procedures currently used to create an auricular prosthesis.

What?
Bionic ear composed of living cells and electronic nanoparticles.

Why?
The printed ear exhibits enhanced auditory sensing for radio frequency reception, and complementary left and right ears can listen to stereo audio music. Overall, our approach suggests a means to intricately merge biological and nanoelectronic functionalities via 3D printing.

What?
Visualization method was used in surgery for cerebral aneurysms. Using the rapid prototyping technology.

Why?
The biomodels were used for diagnosis, operative planning, surgical simulation, instruction for less experienced neurosurgeons, and patient education.

What?
Three-dimensional printed vascular models.

Why?
Provide unprecedented anatomic and volumetric detail and, in addition to assisting in potential treatment planning, can noninvasively provide details needed to determine a surgical or nonsurgical approach for a complex injury.

What?
Creation of a solid skull and the cerebral vessels in different materials to simulate the real aneurysm when clipped.

Why?
Simulation-based training for aneurysm repair.

What?
Surgical training as a learning process for young surgeons or for Ewing's sarcoma in the cervical spine.

Why?
As a result, it is easier for the surgeon to understand the complexity of the case and plan the approach before any surgical procedure.

What?
Anatomically correct 3D rapid prototyping model (RPT) for patients with complex heart disease and altered geometry of the atria or ventricles.

Why?
The use of the 3D rapid prototyping model (RPT-model) during resection of ventricular aneurysm and malignant cardiac tumors may facilitate the surgical procedure due to better planning and improved orientation.

What?
Understanding and treating structural heart disease.

Why?
Current 2-dimensional imaging techniques remain limited both in their ability to represent the complex 3-dimensional relationships present in structural heart disease and in their ability to adequately facilitate often complex corrective procedures.

What?
Three-dimensional models of complex congenitally malformed hearts.

Why?
Current imaging techniques, however, do not always provide all the necessary anatomical information in a user-friendly fashion.

What?
Surgical planning and intraoperative orientation with 3DP for aortic valve replacement after previous coronary bypass grafting.

Why?
Resternotomy for aortic valve replacement in patients with previous coronary artery bypass grafting and an internal mammary artery graft may be a surgical problem.

What?
Percutaneous pulmonary valve implantation based on rapid prototyping of right ventricular outflow tract and pulmonary trunk.

Why?
Refine the selection of patients for percutaneous pulmonary valve implantation (PPVI).

What?
Preoperative endovascular simulations in cerebral aneurysm using a patient-specific silicone model.

Why?
Simulations are feasible and helpful for designing a treatment strategy and safe manipulation of endovascular devices by experiencing their behavior before current treatment.

What?
Use of anatomical models for planning of percutaneous pulmonary valved stent implantation.

Why?
Allowed the cardiologist's confidence in patient selection, prosthesis fabrication, and final implantation to be significantly improved.

What?
Use of three-dimensional printing models for preoperative planning of transcatheter valve replacement in a patient with an extreme porcelain aorta.

Why?
Evaluate the potential effects of these constructs for previous surgical planning and simulation of the transcatheter valve replacement.

What?
Use of TangoPlus FullCure 930® is a commercially available rubber-like material that can be used for PolyJet rapid prototyping in the context of experimental cardiovascular modeling.

Why?
The appealing possibility of printing models of non-uniform wall thickness, resembling more closely certain physiological scenarios.

What?
Rapid prototyping was used to transform aortic geometries as measured by contrast-enhanced MR angiography into realistic vascular models with large anatomical coverage.

Why?
Local vascular anatomy and function in the human body is of high interest for the diagnosis and treatment of cardiovascular disease.

What?
Conversion of thoracic aortic vasculature as measured by Magnetic Resonance Imaging into a real physical replica.

Why?
Rapid vessel prototyping allows the creation of a concrete solid replica of a patient's vascular anatomy.

What?
Analysis Challenges and limitations of patient-specific vascular phantom fabrication using 3D Polyjet printing.

Why?
Anatomic models, for medical device testing and physiological condition evaluation.

What?
Combination of tissue printing technology (TP), human cardiac-derived cardiomyocyte progenitor cells (hCMPCs) and biomaterials to obtain a construct with cardiogenic potential for in vitro use or in vivo application.

Why?
With this approach, we were able to generate an in vitro tissue with homogeneous distribution of cells in the scaffold. Printing can be used for defined cell delivery, while retaining functional properties.

What?
Build an appropriate artificial model of the heart that can replace the use of animals for surgical training in trans-apical AVR procedures.

Why?
Trans-apical aortic valve replacement (AVR) is a new and rapidly growing therapy. However, there are only a few training opportunities.

What?
Three-dimensional (3D) models of AAA using a rapid prototyping technique were developed to help surgical trainees learn how to plan for EVAR more effectively.

Why?
The 3D aortic aneurysm model constructed using the rapid prototype technique may significantly improve the ability of trainees to properly plan for EVAR.

What?
Preoperative planning of this type of surgical interventions due to the possibility of preoperative simulation of the insertion of femoral component into the medullary canal with rapid prototype.

Why?
One of the problems we come across in our practice is related to the patients with very disturbed anatomical structures of the hip joint due to the incompatibilities between standard implants and host bone.

What?
The use of medical CT / MRI scanning, three-dimensional reconstruction, anatomical modeling, computer-aided design, RP and computer-aided implantation in treating a complex fracture of acetabulums, calcaneum, and medial condyle of femur (Hoffa's fracture).

Why?
The production of a copy of the fracture or a deformity in a bone with a complex geometry.

What?
To evaluate the use of rapid prototyping in the assessment, classification and preoperative planning of acetabular fractures.

Why?
The complex three-dimensional anatomy of the pelvis and acetabulum make assessment, classification and treatment of fractures of these structures notoriously difficult.

What?
Compare the diagnostic performance of stereolithography vs workstation-based three-dimensional (3D) reformations in intra-articular calcaneal fractures.

Why?
Based on our results stereolithographs did not prove to be statistically superior to workstation-based 3D reformations. Stereolithographs may still be useful for teaching purposes and for surgical planning at a thinking-efficacy level.

What?
A 6 year old girl presented with a large osteochondroma arising from the scapula. Radiographs, CT and MRI were performed to assess the injury and to determine whether the injury could be safely resected.

Why?
The model allowed better anatomical understanding of the injury and helped plan surgical management.

What?
The aim of this study was to attempt to increase the accuracy of treatment by use of 3-dimensional (3D) computer-aided design. We describe a novel method for ensuring an accurate osteotomy method in the treatment of cubitus varus deformity in teenagers by means of 3D reconstruction and reverse engineering.

Why?
Treatment of cubitus varus deformity from a malunited fracture is a challenge. Anatomically accurate correction is the key to obtaining good functional outcomes after corrective osteotomy.

What?
Surgical training as a learning process for young surgeons or for Ewing's sarcoma in the cervical spine.

Why?
As a result, it is easier for the surgeon to understand the complexity of the case and plan the approach before any surgical procedure.

What?
We depict this method as it pertains to repair of the Charcot foot, it could also be used to plan and practice, or revise, 3-dimensional surgical manipulations of other complex foot deformities.

Why?
Charcot foot syndrome (Charcot neuroarthropathy affecting the foot), particularly in its later stages, may pose a significant technical challenge to the surgeon.

What?
We used specific templates created using a rapid prototyping machine based on the patients' anatomy, to aid in accurate intraoperative pin placement.

Why?
Hip resurfacing arthroplasty (HRA) is a technically demanding operation, requiring both accuracy and precision in placement of the acetabular and femoral components. Malalignment of the component can lead to notching and possible femoral neck fractures.

What?
Describe a method for computer-assisted distal radius osteotomies in which computer-generated, patient-specific plastic guides are used for intraoperative guidance.

Why?
This allows for unique positioning of the guide during surgery. For each planned drill location, a guidance hole is incorporated into the guide. The guides are easy to integrate into the surgical workflow and minimize the need for intraoperative fluoroscopy for guidance of the procedure.

What?
Surgical guides (patientspecific instruments) for pediatric tibial bone sarcoma resection and allograft reconstruction a method for decreasing the resection margin width and ensuring that the margins are adequate. This method was developed in the tibia, which is a common site for the most frequent primary bone sarcomas in children.

Why?
To achieve local control of malignant pediatric bone tumors and to provide satisfactory oncological results, adequate resection margins are mandatory. The local recurrence rate is directly related to inappropriate excision margins.

What?
The procedure and results of subsequent modified wedge osteotomy aided by the techniques of computer-aided design-rapid prototyping (CAD-RP) to correct thoracic deformities.

Why?
The correction of severe thoracic deformities is challenging. However, the usual imaging modalities are not sufficient for performing the surgery

What?
Custom design is based on a Computed Tomography scan of the patient's joint. The proposed design will customize both the articulating surface and the bone-implant interface to address the most common problems found with conventional knee-implant components.

Why?
The longevity of cementless implant components is highly dependent on the initial fit between the bone surface and the implant. The bone-implant interface design has historically been limited by the surgical tools and cutting guides available; and the cost of manufacturing custom-designed implant components has been prohibitive.

What?
Rapid prototyping was used as a tool for manufacturing the custom-made implant.

Why?
Limited visualization of closed internal structures, influence of surgery on airway, presence of teeth and their relationship with the bone, and interference with occlusion often make the surgery complex and unpredictable.

What?
Thoracoscopic pulmonary segmentectomy was performed using the fissureless technique simulated by three-dimensional (3D) pulmonary models.

Why?
The 3D model and rapid prototyping provided an accurate anatomical understanding of the operative field in both cases. We believe that the construction of these models is useful for thoracoscopic and other complicated surgeries of the chest.

What?
Construction of mediastinal models is useful for thoracoscopic surgery and other complicated surgeries of the chest diseases.

Why?
Preoperative three-dimensional (3D) imaging of a mediastinal tumor using two-dimensional (2D) axial computed tomography is sometimes difficult, and an unexpected appearance of the tumor may be encountered during surgery.

What?
Rapid prototyping (RP) technology to create anatomically congruent models of tracheo-bronchial tree for teaching relevant bronchoscopic anatomy.

Why?
RP can be successfully used to create anatomically accurate models from imaging studies. There is potential for RP to become a valuable educational tool in the future.

What?
Three-dimensional image reconstruction by volume rendering and rapid prototyping has made it possible to visualize anatomical structures in three dimensions for interventional planning and academic research.

Why?
Using the rapid-prototype model with hyperpolarized helium-3 magnetic resonance imaging shows the value of this model for flow phantom studies.

What?
In an infant with tracheobronchomalacia, we implanted a customized, bioresorbable tracheal splint, created with a computer-aided design based on a computed tomographic image of the patient's airway and fabricated with the use of laser-based three-dimensional printing, to treat this life. -threatening condition

Why?
We reasoned that the localized tracheobronchomalacia was the cause of this physiological abnormality and made a custom-designed and custom-fabricated resorbable airway splint.

What?
We have successfully shown that 3DP can be used to produce vaginal dilators (VD) and vaginal stents (VS) in adult and piglet porcine vaginal tracts.

Why?
Currently available VS and VD exist only in adult sizes that cannot be used safely or comfortably in the pediatric population.

What?
A neonatal head phantom, comprising of an ellipsoidal geometry and including a circular aperture for simulating the fontanel was designed and fabricated,

Why?
Allow an objective assessment of thermal rise in tissues during trans-cranial ultrasonic scanning of pre-term neonates.

What?
3D-printed models of two fetuses with facial clefts.

Why?
3D-printed models can be a useful addition to patient education and can positively impact maternal - fetal bonding.

What?
3D printed models of pediatric cerebrovascular injuries

Why?
Despite the availability of multiplanar imaging, understanding relational 3D anatomy for complex cerebrovascular lesions can be difficult. 3D printing models provide an instantaneous visualization of lesional anatomy from all perspectives, with the added ability to simulate operative approaches with tactile feedback. The model accuracy using intraprocedural assessment and potential benefit through shortened operative time.

What?
A Realistic 3D-Printed Tracheobronchial Tree Model from a 1-Year-Old Girl for Pediatric Bronchoscopy Training. Another interesting AM application reported is the prenatal evaluation of complex patient-specific fetal anatomy that was subsequently used to manage complex perinatal airway anomalies.

Why?
Because the tracheobronchial tree models used for training to date were scaled for adult lungs, and there is a significant variation between adult lungs and the lungs of a neonate or an infant.

What?
Evaluation of complex patient-specific fetal anatomy and facilitates the multidisciplinary approach to perinatal management of complex airway anomalies.

Why?
The neonate was born with a protuberant cleft lip and palate deformity, without airway obstruction, as predicted by the patient-specific model. Anatomical model, in this case, prevented the surgeons from doing any unnecessary surgical procedure, and the child was discharged without the need for airway intervention.

What?
Developed and validated a physical model to investigate the biomechanics of infant head impact, which is the single most common cause of death or permanent disability from injury in children.

Why?
Pediatric head injury cause and effect is poorly understood, as the only source of data for such studies have been infant postmortem human surrogates (PMHS).

What?
Surgical procedure for older children with developmental dysplasia of the hip (DDH).

Why?
The use of 3D-printed navigation templates resulted in reduced operation time, decreased intraoperative X-ray exposure and surgical risk, reduced epiphysis damage, as well as better operative guidance and surgical precision.

What?
A case study about the Viability in the creation of an artificial liver using Rapid prototyping (RP) technologies.

Why?
These technologies might eventually enable the manufacture of human livers to create functional substitutes for treating liver failure or dysfunction. However, the approaches currently used face many challenges, such as the complex branched vascular and bile ductular systems and the variety of cell types, matrices and regulatory factors involved in liver development.

What?
Three-dimensional printed models of the liver plus vascular and biliary structures assisted in preoperative planning and intraoperative orientation in three living-donor liver transplant surgeries. Using standardized preoperative, intraoperative, and postoperative assessments, it is demonstrated identical anatomical and geometric landmarks in the 3D-printed models and native livers.

Why?
Ensuring the safety of donors and recipients is critical. The preoperative identification of the vascular and biliary tract anatomy with 3-dimensional (3D) printing may allow better preoperative surgical planning, avert unnecessary surgery in patients with potentially unsuitable anatomy, and further decrease the complications of liver transplant surgery.

What?
The preoperative identification of the vascular and biliary tract anatomy with 3-dimensional (3D) printing.

Why?
Better preoperative surgical planning.

What?
3D printed the kidneys plus a renal tumor in five patients who were candidates for partial nephrectomy. To construct high-fidelity, patient customized, physical, 3-dimensional (3D) models of renal units with enhancing renal lesions identified on cross-sectional imaging.

Why?
Aid patients, trainees, and clinicians in their understanding, characterization, localization, and extirpation of suspicious renal masses.

What?
Objectives To investigate the impact of three-dimensional (3D) printing on the surgical planning, potential of training and patients' understanding of minimally invasive surgery for renal tumors.

Why?
Generating kidney models of T1N0M0 tumors with 3D printing are feasible with refinements to be performed. Face and content validity was obtained when those models were presented to experienced urologists for making practical planning and training. Understandings of the disease and procedure from patients were well appreciated with this novel technology.

What?
The authors investigated a novel application of patient-specific three-dimensional (3D) printing, to enhance preoperative, multidisciplinary planning in complex, living-donor pediatric kidney transplant.

Why?
We report the new and safe integration of patient-specific 3D printing into pediatric renal transplantation complex. This technique enhances surgical planning and can inform operative feasibility in those cases which would otherwise be uncertain.

What?
A training model to improve technique and understanding of renal anatomy could improve complications related to renal puncture; however, no model currently exists for resident training.

Why?
Percutaneous nephrolithotomy (PCNL) is a popular method to remove kidney stones; however, broader use by the urological community has been hampered by the morbidity associated with needle puncture to gain access to the renal calix (bleeding, pneumothorax, hydrothorax, inadvertent colon injury).

What?
One-way antireflux valves for ureteral stents.

Why?
The 3D printing takes advantage of an effective miniaturization, and high level of precision and reproducibility to generate one-way valves for ureteral stents to reduce retrograde flow of urine.

What?
Trocars for laparoscopic surgery have also been manufactured by 3D printing to test the utility of printed surgical equipment to reduce waste and solve potential issues of instruments not being available when needed.

Why?
In this pilot study, 3D printing of ureteral stents and trocars is feasible, and these devices can be deployed in the porcine and cadaver models. Three-dimensional printing is rapidly advancing and may be clinically viable in the future.

What?
3D printing allows to construct onto schaffold in which functional cells of the target organ are printed in a second overlying layerthe. These scaffold should eventually degrade and be replaced by extracellular matrix proteins produced by the functional cells.

Why?
Local treatment administration.

What?
Since the printer software allows the creation of shapes with equivalent volume, tablets of different shapes but containing the same dose can be printed.

Why?
Printing tablets in different shapes and colors to the liking of the child is expected to increase compliance for pediatrics. It is also important to note that the shape of the tablet affects many other attributes including the disintegration and rate of dissolution or rate of drug release.

What?
Medical implants and devices, such as stents and catheters, are treated with active solutions or suspensions for local drug delivery, usually by coating or spray-coating techniques.

Why?
3D printing offers increased efficiency, spatial and volume control for the treatment process.

What?
SPRITAM®, an FDA-approved 3D-printed drug, has a unitary porous structure produced by a 3D printing process that binds powders without compression. This structure allows tablets with up to 1000 mg of levetiracetam to disintegrate within seconds when taken with a sip of water.

Why?
The US Food and Drug Administration (FDA) approved Appreciate Pharmaceuticals Company's 3D-printed SPRITAM levetiracetam for oral use in treating epileptic seizures recently. The prospect of tailor-made drugs that are customized to individual patient need.

What?
A 3D printing monolithic implants of levofloxacin.

Why?
The printed implants showed more porous infrastructure than those prepared by compression; thus, the drug release from the printed implant showed faster and slightly higher burst release than the compressed dosage form18. The implants printed with an inner drug reservoir and inner and outer drug layers were able to show pulsed and bimodal drug release.

What?
A novel extrusion printing system was used to create drug delivery structures wherein dexamethasone-21-phosphate disodium salt (Dex21P) was encapsulated within a biodegradable polymer (PLGA) and water soluble poly (vinyl alcohol) (PVA) configurations

Why?
This approach clearly demonstrates that the extrusion printing technique provides an easy and versatile approach to fabrication of novel drug delivery platforms.

Filaments are melted in fused deposition modeling (FDM) then injected through a nozzle to a bed while cooling and solidifying during extrusion. These printers are inexpensive and fast, but are limited to rigid material. FDM needs a scaffold or bed to support the object during the printing.

SLA is the oldest method which contains liquid in a vat solidified with an ultraviolet (UV) laser controlled by lenses and mirror reflection, while a building platform is moved down for a layer-by-layer fabrication. A lattice structure is created to support the object.

PJ uses jets of liquid to build up thin layers of liquid before UV curing by sliding the head in the x and y axes then a moving platform for the z axis to build up successive layers. PJ is suitable for a wide range of colored materials with specific properties (eg, rubber-like material).

SLS uses a laser to create the surface of an object by sintering a powder. When a layer is done, the build plate is stepping down and covered with a new layer of powder using rollers to keep a constant thickness. At the end of the process, all powder is removed with compressed air and recycled. A wide range of materials are provided for SLS and no scaffold or support material is required since the unsintered powder provides support of the object during 3D printing. 

BJ has a platform covered with powder which is moved down while being solidified with a selective spraying of liquid binder; thus, no support material is needed for the fabrication of the object. This technology offers a wide range of materials as far as a powder can be combined with a liquid with enough viscosity to form droplets38. In addition, mechanical properties of the structures obtained by BJ in medical simulation are generally tuned by postprocessing techniques, such as drying and / or heating. Both have an impact on the mechanical properties of

Human bones are the easiest biological tissues to reproduce by 3D printing as the majority of materials are rigid. The most common option remains acrylonitrile butadiene styrene (ABS) by FDM but powders of plaster and hydroquinone were also used by BJ, as well as a mix of polyamide with glass beads by SLS.

ABS is the same plastic used in water pipe of most home and is the most affordable material in 3D printing. It has proven to be an appropriate bone substitute with good visual and haptic renderings for practicing the drilling with minimized cost, despite the softness of the material.

Most of the 3D printing materials present a lack of realism to mimic adequately a soft human biological tissue; thus, post processing might be required to soften printed structures. For instance, cartilaginous tissues, for tumors in the context of surgical simulation, arteries to practice transcatheter valve replacements, as well as hepatic segment and hearts

The common techniques to produce this kind of structures are BJ, SLA and PJ (both techniques are previously explained).

Multimaterial composites may be the future of 3D printed models since none of the current available materials can mimic elastic and biological tissues. Hence, printing materials containing fibers to adequately control the mechanical behavior of the model are being explored. Mechanical testing can be performed to analyze the biomechanical response of the human tissue by cutting, compressing or tearing apart the material. In this way, multi-material composites may be created based on the capacity of selected materials to mimic the mechanical properties of human tissue.